ENTIRE R3 firmware update

Table of Contents
ENTIRE R3 firmware update #

Firmware updates can be performed from any WiFi equipped device with a web browser. Phone, tablet, PC, MAC. Simply download the firmware file from our download page and upload it to your Entire device.

1.    Download the firmware update package below (For ENTIRE R2 or R1 from this page.)
2.    Unzip the content and save the .img file
3.    Connect your device to the Wi-Fi hotspot of Entire
4.    Open the control page at http://entire
5.    Open the MENU and select “Firmware”
6.    Select the .img file downloaded from our website
7.    Package will be uploaded and decompressed

8.    Confirm Start and check it the STATUS LED turns to Purple
9.    While STATUS LED is Purple, device is rewriting memory, this step is critical for interruption
10.    Once LED turns to RED, device is restarting and making self-check. During self-check device can be restarted.

THERE ARE KNOWN ISSUES WITH LATEST FIRMWARE RELEASES, IF YOU HAVE TROUBLES WITH GEOTAGGING, PLEASE USE PREVIOUS VERSIONS UNTIL PROBLEMS WILL BE RESOLVED.

  • extended interval trigger to set up to 0.7s interval
  • corrected control for Sony LR1 during geotagging
  • correction of timing of geotagging

  • added optiion to set 100ms AF time
  • when AF time is set to 300ms or less, ENTIRE uses shorter trigger pulse to achieve faster triggering
  • Sony LR1 control corrections for production firmware
  • Sony LR1 movie triggering in photo mode (available only out of geotagging session)
  • BT scannig correction
  • Correction of camera XYZ offset input system (website correction)
  • Extended values of GPS delay from -120ms to +120ms

  • Added initial support for LR1 serial controller (LR1 Expander)
  • Mavlink compatibility enhancement in GPS/ATTITUDE stream requesting for PX4
  • Correction of Geotagging initialization for ADTi cameras
  • Geotagging accuraccy (processing) improvement
  • Added option to set up to -100ms GPS delay offset

  • New option to HW trigger AF separately for compatible ADTi cameras
  • Corrected issues with detection of ENTIRE HW revision
  • Correction for RED RCP1 WiFi control
  • Include 1.849:
    • correction of control for Fuji GFX100s
    • correction of ISO control for A7RV
    • correction of Exposure compensation for A7RV
    • correction of AF triggering at A7RV

  • enhanced stability of geotagging initialization
  • corrected saving of setting when .cfg file uploaded
  • corrected geotagging of UTC time
  • corrected exposure control for some Sony models
  • added support for Sony ILX-LR1 geotagging and camera control
  • added support for NMEA input at 230400bps
  • added option to EXIF(XMP) tag IMU Accuracy
  • added option to EXIF(XMP) tag Focal Plane Resolution in um
  • added alpha support for UBX protocol (supported under NMEA port mode)

  • added function of moving focuspoint for Canon R5 via USB
  • added HW trigger option for ADTi cameras
  • Newly “Force SBUS” under Gremsy is by default set to OFF
  • Added option to add up to 100ms GPS link delay
  • Enhanced informational log content
  • Correction of EXIF geotagging compatibility

 

  • MavPorter support
  • Corrections of webUI
  • Correction of Gremsy gimbal tuning tool for FW773
  • New feature to output equivalent of actual gimbal tilt to SBUS output (via SBUS out mapping)
  • Correction of IR triggering for Sony
  • New options for fixed camera mount (geotagging)
  • Improved behavior of WiFi connection and re-connection to RED KOMODO (X) / V-RAPTOR
  • New support of INRASTRUCTURE WiFi connection mode for RED KOMODO (X), V-RAPTOR. New mode is faster and much more user friendly (no dropouts of ENTIRE hotspot)
  • New control features for RED KOMODO | V-RAPTOR
  • New Support for RED serial control cable (available in few weeks)
  • New option to XMP geotag Roll/Pitch/Yaw
  • Reworked geotagging settings submenu to be more understandable
  • New option to append GPSXYAccuracy and GPSZAccuracy into TXT log
  • Correction of ENTIRE system ID (from 133 to 1)

———————-

  • BETA features (accuracy or stability needs to be tested):
    • added option to XMP geotag GPSXYZAccuracy (beta)
    • added option to EXIF geotag GPSDateStamp and GPSTimeStamp with millisecond accuracy (beta)
    • added option to modify ModifyDate in EXIF (beta)
    • added option to modify CreateDate in EXIF (beta)
    • added option to modify DateTimeOriginal in EXIF (beta)

 

  • This firmware may need Validation of HW – read more here
  • Added support to control MENU and navigation on Panasonic BGH1 and BS1H cameras
  • Added configurable pulse length and low, medium, high value for SBUS output
  • Corrected behavior of iXlink triggeting in Event TEXT geotagging mode
  • Geotagging session keeps running under failsafe
  • Correction of Sony ISO control
  • New option to add UTC time of capture to TEXT log (precision of 1ms)
  • New option to set MavLink baudrate 230400
  • New option to configure ENTIRE’s MavLink ID – MavCam work only with default ID – CAMERA6
  • New option to set Geotagging START / STOP function for control via Link
    • This update contains update for ExtensionBOX!
    • ExtensionBOX newly supports MavLink baudrate of 230400 and 1250000bps

  • This firmware may need Validation of HW – read more here
  • New geotagging mode – Event TEXT – very simple even loggging mode applicable basically to all cameras
  • Geotagging modes are newly renamed to Direct EXIF, Full TEXT and Event TEXT
  • Corrected capture detection system for ENTIRE R1 and R2 (R1 and R2 are not using new method with higher accuracy)
  • New ViewPro feature to toggle YAW follow lock ON / OFF via MavCam
  • New ViewPro support for Yaw/Tilt control via on-screen joystick via MavCam
  • Correction of angle offset for EXIF geotagging
  • Correction of triggering and other MavLink commanding

ENTIRE R3 firmware update

Firmware updates can be performed from any WiFi equipped device with a web browser. Phone, tablet, PC, MAC. Simply download the firmware file from our download page and upload it to your Entire device.

1.    Download the firmware update package below (For ENTIRE R2 or R1 from this page.)
2.    Unzip the content and save the .img file
3.    Connect your device to the Wi-Fi hotspot of Entire
4.    Open the control page at http://entire
5.    Open the MENU and select “Firmware”
6.    Select the .img file downloaded from our website
7.    Package will be uploaded and decompressed

8.    Confirm Start and check it the STATUS LED turns to Purple
9.    While STATUS LED is Purple, device is rewriting memory, this step is critical for interruption
10.    Once LED turns to RED, device is restarting and making self-check. During self-check device can be restarted.

THERE ARE KNOWN ISSUES WITH LATEST FIRMWARE RELEASES, IF YOU HAVE TROUBLES WITH GEOTAGGING, PLEASE USE PREVIOUS VERSIONS UNTIL PROBLEMS WILL BE RESOLVED.

  • extended interval trigger to set up to 0.7s interval
  • corrected control for Sony LR1 during geotagging
  • correction of timing of geotagging

  • added optiion to set 100ms AF time
  • when AF time is set to 300ms or less, ENTIRE uses shorter trigger pulse to achieve faster triggering
  • Sony LR1 control corrections for production firmware
  • Sony LR1 movie triggering in photo mode (available only out of geotagging session)
  • BT scannig correction
  • Correction of camera XYZ offset input system (website correction)
  • Extended values of GPS delay from -120ms to +120ms

  • Added initial support for LR1 serial controller (LR1 Expander)
  • Mavlink compatibility enhancement in GPS/ATTITUDE stream requesting for PX4
  • Correction of Geotagging initialization for ADTi cameras
  • Geotagging accuraccy (processing) improvement
  • Added option to set up to -100ms GPS delay offset

  • New option to HW trigger AF separately for compatible ADTi cameras
  • Corrected issues with detection of ENTIRE HW revision
  • Correction for RED RCP1 WiFi control
  • Include 1.849:
    • correction of control for Fuji GFX100s
    • correction of ISO control for A7RV
    • correction of Exposure compensation for A7RV
    • correction of AF triggering at A7RV

  • enhanced stability of geotagging initialization
  • corrected saving of setting when .cfg file uploaded
  • corrected geotagging of UTC time
  • corrected exposure control for some Sony models
  • added support for Sony ILX-LR1 geotagging and camera control
  • added support for NMEA input at 230400bps
  • added option to EXIF(XMP) tag IMU Accuracy
  • added option to EXIF(XMP) tag Focal Plane Resolution in um
  • added alpha support for UBX protocol (supported under NMEA port mode)

  • added function of moving focuspoint for Canon R5 via USB
  • added HW trigger option for ADTi cameras
  • Newly “Force SBUS” under Gremsy is by default set to OFF
  • Added option to add up to 100ms GPS link delay
  • Enhanced informational log content
  • Correction of EXIF geotagging compatibility

 

  • MavPorter support
  • Corrections of webUI
  • Correction of Gremsy gimbal tuning tool for FW773
  • New feature to output equivalent of actual gimbal tilt to SBUS output (via SBUS out mapping)
  • Correction of IR triggering for Sony
  • New options for fixed camera mount (geotagging)
  • Improved behavior of WiFi connection and re-connection to RED KOMODO (X) / V-RAPTOR
  • New support of INRASTRUCTURE WiFi connection mode for RED KOMODO (X), V-RAPTOR. New mode is faster and much more user friendly (no dropouts of ENTIRE hotspot)
  • New control features for RED KOMODO | V-RAPTOR
  • New Support for RED serial control cable (available in few weeks)
  • New option to XMP geotag Roll/Pitch/Yaw
  • Reworked geotagging settings submenu to be more understandable
  • New option to append GPSXYAccuracy and GPSZAccuracy into TXT log
  • Correction of ENTIRE system ID (from 133 to 1)

———————-

  • BETA features (accuracy or stability needs to be tested):
    • added option to XMP geotag GPSXYZAccuracy (beta)
    • added option to EXIF geotag GPSDateStamp and GPSTimeStamp with millisecond accuracy (beta)
    • added option to modify ModifyDate in EXIF (beta)
    • added option to modify CreateDate in EXIF (beta)
    • added option to modify DateTimeOriginal in EXIF (beta)

 

  • This firmware may need Validation of HW – read more here
  • Added support to control MENU and navigation on Panasonic BGH1 and BS1H cameras
  • Added configurable pulse length and low, medium, high value for SBUS output
  • Corrected behavior of iXlink triggeting in Event TEXT geotagging mode
  • Geotagging session keeps running under failsafe
  • Correction of Sony ISO control
  • New option to add UTC time of capture to TEXT log (precision of 1ms)
  • New option to set MavLink baudrate 230400
  • New option to configure ENTIRE’s MavLink ID – MavCam work only with default ID – CAMERA6
  • New option to set Geotagging START / STOP function for control via Link
    • This update contains update for ExtensionBOX!
    • ExtensionBOX newly supports MavLink baudrate of 230400 and 1250000bps

  • This firmware may need Validation of HW – read more here
  • New geotagging mode – Event TEXT – very simple even loggging mode applicable basically to all cameras
  • Geotagging modes are newly renamed to Direct EXIF, Full TEXT and Event TEXT
  • Corrected capture detection system for ENTIRE R1 and R2 (R1 and R2 are not using new method with higher accuracy)
  • New ViewPro feature to toggle YAW follow lock ON / OFF via MavCam
  • New ViewPro support for Yaw/Tilt control via on-screen joystick via MavCam
  • Correction of angle offset for EXIF geotagging
  • Correction of triggering and other MavLink commanding